Home | About | FAQ | Shipping Policies | Extras and Deals | Custom Options | Contact Us
299 Craftsman Sockets
Fits (64) 1/4-drive sockets,
(109) 3/8-drive sockets,
and (126) 1/2-drive sockets.
Accommodates all sockets from the 299-piece Craftsman set 35299.
Caution: Recommended for a 4-inch or deeper drawer.
Pockets sized to fit the 1st version of this set with "USA" markings.
Drawer Size
36-1/2 X 16-1/4 inches
$100.90
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 299 Craftsman sockets:
(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(10) 1/4-drive 12-point sizes from 3/16 to 9/16
(10) 1/4-drive 6-point deep sizes from 3/16 to 9/16
(10) 1/4-drive 12-point deep sizes from 3/16 to 9/16
(13) 3/8-drive 6-point sizes from 1/4 to 1
(5) 3/8-drive 8-point sizes from 1/4 to 1/2
(13) 3/8-drive 12-point sizes from 1/4 to 1
(11) 3/8-drive 6-point deep sizes from 3/8 to 1
(11) 3/8-drive 12-point deep sizes from 3/8 to 1
(15) 1/2-drive 6-point sizes from 3/8 to 1-1/4
(6) 1/2-drive 8-point sizes from 7/16 to 3/4
(19) 1/2-drive 12-point sizes from 3/8 to 1-1/2
(11) 1/2-drive 6-point deep sizes from 1/2 to 1-1/8
(13) 1/2-drive 12-point deep sizes from 7/16 to 1-3/16
(12) 1/4-drive 6-point sizes from 4 to 14
(11) 1/4-drive 6-point deep sizes from 4 to 14
(17) 3/8-drive 6-point sizes from 6 to 22
(15) 3/8-drive 12-point sizes from 6 to 21
(11) 3/8-drive 6-point deep sizes from 9 to 19
(13) 3/8-drive 12-point deep sizes from 9 to 22
(14) 1/2-drive 6-point sizes from 9 to 22
(24) 1/2-drive 12-point sizes from 9 to 36
(9) 1/2-drive 6-point deep sizes from 12 to 21
(15) 1/2-drive 12-point deep sizes from 10 to 27
This tool organizer was designed to fit the sockets from the original version of the Craftsman 299-piece set 35299. The pockets are sized to fit sockets with "U.S.A." markings only.
36-1/2 X 16-1/4 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 35-7/8 X 15-3/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.