Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
16 Craftsman Reversible Ratcheting Wrenches and 5 Tappet Wrenches, Fits non-USA Wrenches
Overview
16 Craftsman Reversible Ratcheting Wrenches and 5 Tappet Wrenches, Fits non-USA Wrenches
Fits (8) reversible inch ratcheting wrenches, (8) reversible metric ratcheting wrenches, and (5) inch tappet wrenches.
Note: this organizer fits the ratcheting wrenches and tappet wrenches from the newer version of the Craftsman 540-piece mechanics tool set (see Craftsman 35540).
Drawer Size
22-1/4 X 14-1/2 inches
$43.00
Details
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 21 Craftsman wrenches:
inch reversible ratcheting wrenches:
5/16 (Craftsman 42412)
3/8 (Craftsman 42413)
7/16 (Craftsman 42414)
1/2 (Craftsman 42415)
9/16 (Craftsman 42416)
5/8 (Craftsman 41417)
11/16 (Craftsman 41418)
3/4 (Craftsman 42419)
inch tappet wrenches:
3/8 X 7/16 (Craftsman 47467)
7/16 X 17/32 (Craftsman 04747)
1/2 X 9/16 (Craftsman 47464 or 47474)
5/8 X 11/16 (Craftsman 47468)
3/4 X 7/8 (Craftsman 47465)
metric reversible ratcheting wrenches:
8mm (Craftsman 42420)
10mm (Craftsman 42421)
11mm (Craftsman 42422)
12mm (Craftsman 42423)
13mm (Craftsman 42424)
14mm (Craftsman 42425)
15mm (Craftsman 42426)
16mm (Craftsman 42427)
This tool organizer was designed to fit the reversible ratcheting wrenches and tappet wrenches from version 2 of the Craftsman 540-piece set (see Craftsman 35540). The pockets are sized to fit tools that don't have "USA" markings.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Drawer Size
This organizer is designed to fit a toolbox drawer with inner dimensions of:
22-1/4 X 14-1/2 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 14-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1M-01049.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
