FoamFit Tools section divider

Foam Tool Organizer for
14 Craftsman Inch Full-Polish Combination Wrenches, Fits non-USA Wrenches

see all organizers for combination wrenches

Overview

14 Craftsman Inch Full-Polish Combination Wrenches, Fits non-USA Wrenches

Fits (14) wrenches:
5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/8

Accommodates the combination wrenches from the Craftsman 24-piece inch wrench set 45024.

Drawer Size
22-1/4 X 16-1/4 inches

$46.50



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 14 Craftsman wrenches:

inch combination wrench sizes:
5/16 (Craftsman 45974)
3/8 (Craftsman 45975)
7/16 (Craftsman 45976)
1/2 (Craftsman 45977)
9/16 (Craftsman 45978)
5/8 (Craftsman 45979)
11/16 (Craftsman 45980)
3/4 (Craftsman 45981)
13/16 (Craftsman 45982)
7/8 (Craftsman 45983)
15/16 (Craftsman 45984)
1 (Craftsman 45985)
1-1/16 (Craftsman 45950)
1-1/8 (Craftsman 45951)

This tool organizer was designed to fit the inch combination wrenches from the Craftsman 24-piece wrench set 45024. The pockets only fit full-polish wrenches that don't have "USA" markings.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for Craftsman Full-Polish Inch Combination Wrenches from the 24-Piece Wrench Set

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 16-1/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 22 X 15-3/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1M-01408.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site