Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
87 Craftsman Impact Sockets with 8 Accessories
Overview
87 Craftsman Impact Sockets with 8 Accessories
Fits (38) 3/8-drive impact sockets, (49) 1/2-drive impact sockets, (5) impact extensions, and (3) impact adapters.
Accommodates all tools from the 95-piece impact socket set 15383.
Caution: Recommended for a 3.75-inch or higher drawer.
Drawer Size
22-1/4 X 16-1/4 inches
$61.50
Details
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 95 Craftsman impact tools:
(9) 3/8-drive 6-point impact sizes from 1/4 to 3/4
(9) 3/8-drive 6-point impact deep sizes from 1/4 to 3/4
(12) 1/2-drive 6-point impact sizes from 3/8 to 1-1/16
(12) 1/2-drive 6-point impact deep sizes from 3/8 to 1-1/16
(10) 3/8-drive 6-point impact sizes from 10 to 19 mm
(10) 3/8-drive 6-point impact deep sizes from 10 to 19 mm
(12) 1/2-drive 6-point impact sizes 12 to 19, 21, 22, 24, and 27 mm
(12) 1/2-drive 6-point impact deep sizes 12 to 19, 21, 22, 24, and 27 mm
3/8 X 3 impact extension 19496
3/8 X 6 impact extension 19497
1/2 X 3 impact extension 19498
1/2 X 6 impact extension 19493
1/2 X 10 impact extension 19499
1/2 to 3/8 impact adapter 19494
3/8 impact universal joint 19491
1/2 impact universal joint 19492
3/4 X 13/16 (1/2-drive) double-ended impact socket 19495
This tool organizer was designed to fit the inch and metric impact sockets and additional tools from the Craftsman 95-piece set 15383.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Drawer Size
This organizer is designed to fit a toolbox drawer with inner dimensions of:
22-1/4 X 16-1/4 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 14-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1A-01619.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
