Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
16 Craftsman Stubby and 10 Flare-Nut Wrenches, Fits non-USA Wrenches
Overview
16 Craftsman Stubby and 10 Flare-Nut Wrenches, Fits non-USA Wrenches
Fits (8) inch stubby combination wrenches, (5) inch flare-nut wrenches, (8) metric stubby combination wrenches, and (5) metric flare-nut wrenches.
Accommodates the stubby and flare-nut wrenches from the Craftsman 903-pc set 21470.
Drawer Size
22-1/4 X 16-1/4 inches
$46.50
Details
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 26 Craftsman wrenches:
inch stubby combination wrenches:
3/8 (Craftsman 44103)
7/16 (Craftsman 44104)
1/2 (Craftsman 44105)
9/16 (Craftsman 44106)
5/8 (Craftsman 44107)
11/16 (Craftsman 44108)
3/4 (Craftsman 44109)
13/16 (Craftsman 44099)
inch flare-nut wrenches:
1/4 X 5/16 (Craftsman 42090)
3/8 X 7/16 (Craftsman 42091)
1/2 X 9/16 (Craftsman 42092)
5/8 X 11/16 (Craftsman 42093)
3/4 X 7/8 (Craftsman 42094)
metric stubby combination wrenches:
10mm (Craftsman 44113)
12mm (Craftsman 44114)
13mm (Craftsman 44115)
14mm (Craftsman 44116)
15mm (Craftsman 44117)
17mm (Craftsman 44118)
18mm (Craftsman 44119)
19mm (Craftsman 44120)
metric flare-nut wrenches:
9 X 11 (Craftsman 42095)
10 X 12 (Craftsman 42096)
13 X 14 (Craftsman 42097)
15 X 17 (Craftsman 42098)
16 X 18 (Craftsman 42099)
This tool organizer was designed to fit the stubby and flare-nut wrenches from the Craftsman 903-pc set 21470. The pockets are sized to fit tools that don't have "USA" markings.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Drawer Size
This organizer is designed to fit a toolbox drawer with inner dimensions of:
22-1/4 X 16-1/4 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1M-01997.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
