FoamFit Tools section divider

Foam Tool Organizer for
20 Tekton Screwdriver Set

see all organizers for Tekton

Overview

20 Tekton Screwdriver Set

Fits (7) slotted, (7) phillips, and (6) torx screwdrivers.

Accommodates the high-torque black oxide screwdrivers from set DRV41216, torx set DHT91006, and two additional tools. Also fits screwdrivers with chrome blades.

May be trimmed to fit a variety of drawer sizes.

New!

Drawer Size
24 X 18 inches

$52.20



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 20 Tekton screwdrivers:

slotted:
1/4 X 1-1/2 (Tekton 26621 or DHS30250)
1/8 X 4 (Tekton 26603 or DHS31125)
3/16 X 4 (Tekton 26613 or DHS31188)
1/4 X 4 (Tekton 26623 or DHS31250)
5/16 X 4 (Tekton 26633 or DHS31313)
3/16 X 8 (Tekton 26615 or DHS34188)
1/4 X 8 (Tekton 26625 or DHS34250)

phillips:
#2 X 1-1/2 (Tekton 26671 or DHP30002)
#0 X 4 (Tekton 26653 or DHP31000)
#1 X 4 (Tekton 26663 or DHP31001)
#2 X 4 (Tekton 26673 or DHP31002)
#3 X 4 (Tekton 26683 or DHP31003)
#1 X 8 (Tekton 26665 or DHP34001)
#2 X 8 (Tekton 26675 or DHP34002)

torx:
T10 X 4 (Tekton 26801 or DHT31100)
T15 X 4 (Tekton 26802 or DHT31150)
T20 X 4 (Tekton 26803 or DHT31200)
T25 X 4 (Tekton 26804 or DHT31250)
T27 X 4 (Tekton 26805 or DHT31270)
T30 X 4 (Tekton 26806 or DHT31300)

This tool organizer was designed to fit the 20 Tekton screwdrivers from black oxide set DRV41216 and DHT91006, or chrome sets DRV43007 and DHT43001, plus individual screwdrivers 5/16 X 4 and #3 X 4.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 20 Tekton screwdrivers

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

24 X 18 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03576-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site