Home | About | FAQ | Shipping Policies | Extras and Deals | Custom Options | Contact Us
31 Craftsman Screwdriver Set #1
Fits (9) slotted screwdrivers,
(7) Phillips screwdrivers,
(6) torx screwdrivers,
(1) pocket screwdriver,
(3) offset screwdrivers,
(1) square screwdriver, and (4) mini picks.
Accommodates 31 screwdrivers including 25-piece set CMHT65046 plus six additional Craftsman screwdrivers.
Designed to fit the newer hard handle screwdrivers made in Taiwan. Fit may not be optimal for USA or China versions.
Drawer Size
22-1/4 X 14-1/2 inches
$43.00
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 31 Craftsman screwdrivers:
slotted:
3/32 X 1-1/2
1/8 X 2-1/2 (CMHT65017)
1/8 X 4 (CMHT65018)
3/16 X 4 (CMHT65021)
3/16 X 8 (cabinet) (CMHT65084)
1/4 X 1-1/2 (CMHT65013)
1/4 X 4 (CMHT65014)
1/4 X 6 (CMHT65015)
5/16 X 6 (CMHT65030)
Phillips:
P0 X 1-1/2
P0 X 2-1/2 (CMHT65000)
P1 X 3 (CMHT65002)
P2 X 1-1/2 (CMHT65003)
P2 X 4 (CMHT65004)
P2 X 6 (CMHT65005)
P3 X 6 (CMHT65009)
torx:
T10 X 3 (CMHT65035)
T15 X 3 (CMHT65036)
T20 X 3 (CMHT65037)
T25 X 4 (CMHT65038)
T27 X 4 (CMHT65039)
T30 X 4 (CMHT65040)
other screwdrivers:
(1) square #2 X 4 (CMHT65033)
(4) mini-picks
(3) offset screwdrivers
(1) pocket/keychain
This tool organizer was designed to fit the 25-Piece Craftsman screwdriver set CMHT65046, plus pockets for (6) additional screwdrivers: CMHT65018, CMHT65084, CMHT65030, CMHT65009, CMHT65039, and CMHT65040.
22-1/4 X 14-1/2 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 14-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.