Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
22-pc Tekton Hard-Handle Screwdriver Set
Overview
22-pc Tekton Hard-Handle Screwdriver Set
Fits (8) slotted, (8) phillips, and (6) torx screwdrivers.
Accommodates the black oxide screwdrivers from set DRV40122 or chrome screwdrivers from set DRV42020.
May be trimmed to fit a variety of drawer sizes.
Drawer Size
24 X 18 inches
$52.20
Details
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 22 Tekton screwdrivers:
slotted:
1/4 X 1-1/2 (Tekton 30250 or 10250)
1/8 X 4 (Tekton 31125 or 11125)
3/16 X 4 (Tekton 31188 or 11188)
1/4 X 4 (Tekton 31250 or 11250)
5/16 X 4 (Tekton 31313 or 11313)
3/16 X 8 (Tekton 34188 or 14188)
1/4 X 8 (Tekton 34250 or 14250)
5/16 X 8 (Tekton 34313 or 14313)
phillips:
#2 X 1-1/2 (Tekton 30002 or 10002)
#0 X 4 (Tekton 31000 or 11000)
#1 X 4 (Tekton 31001 or 11001)
#2 X 4 (Tekton 31002 or 11002)
#3 X 4 (Tekton 31003 or 11003)
#1 X 8 (Tekton 34001 or 14001)
#2 X 8 (Tekton 34002 or 14002)
#3 X 8 (Tekton 34003 or 14003)
torx:
T10 X 4 (Tekton 31100 or 11100)
T15 X 4 (Tekton 31150 or 11150)
T20 X 4 (Tekton 31200 or 11200)
T25 X 4 (Tekton 31250 or 11250)
T27 X 4 (Tekton 31270 or 11270)
T30 X 4 (Tekton 31300 or 11300)
This tool organizer was designed to fit the 22-piece Tekton screwdriver set DRV40122 with black oxide blades or set DRV42020 with chrome blades. It also works for older sets DRV40115 and DRV42012.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Drawer Size
This organizer is designed to fit a toolbox drawer with inner dimensions of:
24 X 18 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-1/2 X 15-3/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-03762-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
