Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
11 Channellock Pliers, 1 Adjustable Wrench and 12 Wright Screwdrivers
Overview
11 Channellock Pliers, 1 Adjustable Wrench and 12 Wright Screwdrivers
Fits (6) slotted screwdrivers, (6) Phillips screwdrivers, (11) Channellock pliers, and (1) adjustable wrench.
Caution: older versions of the E326 and E318 long nose pliers may not fit.
Drawer Size
36-1/2 X 16-1/4 inches
$76.20
Details
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 24 Wright tools:
Slotted screwdrivers:
1/8 X 3 (Wright 9112)
3/16 X 4 (Wright 9115)
1/4 X 1-1/2 (Wright 9122)
1/4 X 6 (Wright 9124)
5/16 X 6 (Wright 9125)
3/8 X 8 (Wright 9135)
Phillips screwdrivers:
P0 X 3 (Wright 9103)
P1 X 3 (Wright 9104)
P2 X 1-1/2 (Wright 9101)
P2 X 4 (Wright 9105)
P2 X 8 (Wright 9108)
P3 X 6 (Wright 9106)
Pliers:
9.5-inch crimping pliers (Channellock 909)
7-inch cutting (diagonal) pliers (Channellock 437)
7.5-inch lineman's pliers (Channellock 367)
6.5-inch slip joint pliers (Channellock 526)
6-inch long nose pliers (Channellock E326)
8-inch long nose pliers (Channellock E318)
8-inch bent nose pliers with cutter (Channellock E388)
8-inch long reach (duckbill) pliers (Channellock 718)
9.5-inch tongue and groove pliers (Channellock 420)
7-inch wire stripper for 10-20 AWG (Channellock 957)
8-inch retaining ring pliers (Channellock 927)
8-inch adjustable wrench, 1.5-inch capacity (Channellock 8WCB)
The screwdrivers and pliers for this organizer are not sold as a set. Contact Customer Service if you need help finding any of the tools.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Drawer Size
This organizer is designed to fit a toolbox drawer with inner dimensions of:
36-1/2 X 16-1/4 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 35-3/4 X 15-3/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-03810-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
