Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
27 Tekton Inch Combination and Stubby Wrenches
Overview
27 Tekton Inch Combination and Stubby Wrenches
Fits (19) inch combination wrenches and (8) stubby inch wrenches.
Sized to fit the Tekton 36 X 24 inch tool cabinet (ORG72200 or ORG72100). Please measure your drawer before ordering.
Drawer Size
31-7/16 X 20-9/16 inches
$83.00
Details
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 27 Tekton wrenches:
inch combination sizes:
1/4 (Tekton 18251)
9/32 (Tekton 18252)
5/16 (Tekton 18253)
11/32 (Tekton 18254)
3/8 (Tekton 18255)
7/16 (Tekton 18256)
1/2 (Tekton 18257)
9/16 (Tekton 18258)
5/8 (Tekton 18259)
11/16 (Tekton 18261)
3/4 (Tekton 18262)
13/16 (Tekton 18263)
7/8 (Tekton 18264)
15/16 (Tekton 18265)
1 (Tekton 18266)
1-1/16 (Tekton 18267)
1-1/8 (Tekton 18268)
1-3/16 (Tekton 18269)
1-1/4 (Tekton 18271)
inch stubby sizes:
5/16 (Tekton 18043)
3/8 (Tekton 18045)
7/16 (Tekton 18046)
1/2 (Tekton 18047)
9/16 (Tekton 18048)
5/8 (Tekton 18049)
11/16 (Tekton 18051)
3/4 (Tekton 18052)
This tool organizer was designed to fit Tekton wrench sets WCB1102 and WRN01066.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Drawer Size
This organizer is designed to fit a toolbox drawer with inner dimensions of:
31-7/16 X 20-9/16 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 29-1/8 X 20-1/8 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-03827-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
