FoamFit Tools section divider

Foam Tool Organizer for
22 Husky Drive Tools with 2 Ratchets and 15 Long Hex Bit Sockets

see all organizers for Husky tools

Overview

22 Husky Drive Tools with 2 Ratchets and 15 Long Hex Bit Sockets

Fits (2) flex head ratchets, (2) palm ratchets, (13) extensions, (15) long hex bit sockets, (1) spinner handle, (5) breaker bars, and (1) T-handle.

Accommodates the drive tools and long hex bit sockets from the Husky 1025-pc set H1025MTS.

New!

Drawer Size
33-13/16 X 19-3/4 inches

$85.80



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 24 Husky drive tools and 15 hex bit sockets:

drive tools:
1/4-drive breaker bar
1/4 X 2 extension
1/4 X 3 extension
1/4 X 6 extension
1/4-drive spinner handle
1/4-drive palm ratchet
3/8-drive flex head ratchet
3/8-drive palm ratchet
3/8-drive breaker bar
3/8 X 1-1/2 extension
3/8 X 3 extension
3/8 X 6 extension
3/8 X 8 flex extension
3/8 X 10 extension
3/8 X 20 extension
1/2-drive flex head ratchet
1/2-drive X 14 inch breaker bar
1/2-drive X 24 inch breaker bar
1/2-drive T-handle
1/2-drive speeder breaker bar
1/2 X 3 extension
1/2 X 5 extension
1/2 X 10 extension
1/2 X 20 extension

long ball-end hex bit sockets:
(7) 3/8-drive sizes from 1/8 to 3/8
(8) 3/8-drive sizes from 3 to 10 mm

This tool organizer was designed to fit the flex head ratchets, palm ratchets, breaker bars, extensions, long hex bit sockets, and other drive tools from the Husky 1025-pc set H1025MTS.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 22 Husky Drive Tools with 2 Ratchets and 15 Long Hex Bit Sockets

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

33-13/16 X 19-3/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 31-15/16 X 18-3/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03919-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site