Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
31 Husky Metric Crow Foot, Midget, Box End, and Flare-Nut Wrenches
Overview
31 Husky Metric Crow Foot, Midget, Box End, and Flare-Nut Wrenches
Fits (10) crow foot wrenches, (6) flare-nut wrenches, (10) midget wrenches, and (5) deep-offset box wrenches.
Accommodates the metric crow foot, flare-nut, midget, and box end wrenches from the Husky 1025-pc set H1025MTS.
Drawer Size
14-15/16 X 19-3/4 inches
$40.70
Details
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 31 Husky wrenches:
crow foot wrenches:
3/8-drive 10 mm
3/8-drive 11 mm
3/8-drive 12 mm
3/8-drive 13 mm
3/8-drive 14 mm
3/8-drive 15 mm
3/8-drive 16 mm
3/8-drive 17 mm
3/8-drive 18 mm
3/8-drive 19 mm
flare-nut wrenches:
9 X 11 (HFNW911MM)
10 X 12 (HFNW1012MM)
13 X 14 (HFNW1314MM)
15 X 17
16 X 18
19 X 21
midget wrenches:
4 mm
4.5 mm
5 mm
5.5 mm
6 mm
7 mm
8 mm
9 mm
10 mm
11 mm
metric box end wrenches:
8 X 10
10 X 12
11 X 13
12 X 14
17 X 19
This tool organizer was designed to fit the metric crow foot, midget, box end, and flare-nut wrenches from the Husky 1025-pc set H1025MTS.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Drawer Size
This organizer is designed to fit a toolbox drawer with inner dimensions of:
14-15/16 X 19-3/4 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 14-7/16 X 19-3/8 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-03924-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
